Mini Book Cover Maker

About Mini Book Cover Maker: Print Covers for Tiny & 3D Printed Books

It looks for the two straight vertical edges near the middle of the picture that run its whole height, which is where a printed cover changes from back to spine and spine to front. Two lines show where it cut.

By the ToolFluency team · Updated November 2026

Turn any cover picture into a printable wrap for a miniature or 3D printed book. Finds the spine, fits front, spine and back to size, prints at true scale.

How to use

  1. Add your cover picture in step 1: one picture with the back, spine and front side by side (a scan of the whole cover, or a DVD-style wrap). Choose it, drop it on the preview, or paste it. You can also load the three pieces separately.
  2. Set the book size in step 2: the full-size book (width, height, thickness) and the scale of your model. 1:12 is dollhouse scale; 1:6 suits fashion dolls. Read the size from an STL file to take it straight from your 3D model. Pick Rounded for a hardcover spine, Flat for a paperback or a box.
  3. Check the spine in step 3. The two lines on your picture are placed on the spine automatically; drag them on the picture if they are off. The 3D book and the print sheet beside it update as you drag.
  4. If the cover is still on the book, open the Clean up tab. Drag the four dots on your photo onto the corners of the whole cover to straighten it, then even out the lighting, turn on auto colour or sharpen it as needed. The book updates as you go, and Undo all clean-up returns to your original photo.
  5. On the Fit tab, choose how each piece fills its panel: crop to fill, stretch to fill, or fit the whole picture. Drag the 3D book to turn it and check the front, spine and back.
  6. Print in step 4 at 100 percent (Actual size). Measure the 50 mm bar, cut along the solid edge, fold at the marks and glue the wrap around the book. Download PNG gives you the same wrap at 300 dpi.

Frequently asked questions

How does it know where the spine is?

It looks for the two straight vertical edges near the middle of the picture that run its whole height, which is where a printed cover changes from back to spine and spine to front. Two lines show where it cut. If they are off, slide them onto the spine edges and the preview updates as you go.

My cover will not come off the book. Can I still use a photo of it?

Yes. Take the photo straight over the book with light from the side and no flash. Then, in step 3, open Clean up and drag the four dots on your photo onto the corners of the cover. It straightens the photo to the exact shape of your wrap, and you can even out the shadow near the spine, correct faded or yellowed colour, and enlarge and sharpen a small photo. The 3D book shows the result as you go. Glare from a shiny cover cannot be removed afterwards, so avoid it when you take the photo.

What size should I enter?

Enter the full-size book (width, height and thickness) and the scale you printed it at, for example 25 percent. If you have the 3D model, press Read size from STL and the size comes from the file. For a book you made at its final size, leave the scale at 100.

Why is my rounded spine wider than the book is thick?

Paper wrapped around a rounded spine travels further than a straight line across it. The tool measures the curve, so the spine panel comes out a little wider than the thickness. Pick Flat for a paperback, a box or a square spine.

Will the picture be squashed?

Only if you ask for it. The front and back crop to fill their panels by default, trimming a little off the edges if the shapes differ. The spine stretches by default because spine strips are usually much thinner than the book. Each piece can be set to crop, stretch or fit whole.

How do I make sure it prints the right size?

Print at 100 percent or Actual size, not Fit to page. Each sheet has a 50 mm bar; measure it with a ruler. If it is not 50 mm, your print settings are scaling the page.

What paper and glue work best?

Thin paper wraps a small spine best: plain 20 lb paper or thin glossy photo paper. Cardstock cracks on the folds at small sizes. A glue stick or spray adhesive keeps the paper flat; white glue soaks in and wrinkles it.

Are my pictures uploaded anywhere?

No. Everything happens in your browser. The pictures are never sent to a server.

Part of ToolFluency’s library of free online tools for Creative. No account needed, no data leaves your device.

Embed this tool on your site (free)
Paste this where you want the tool. Please keep the attribution link.
<iframe id="tf-mini-book-cover-maker" src="https://toolfluency.com/tools-v2/creative/mini-book-cover-maker.html?embed=1" width="100%" height="640" loading="lazy" style="border:1px solid #e2e2e2;border-radius:12px;max-width:760px" title="Mini Book Cover Maker: Print Covers for Tiny &amp; 3D Printed Books by ToolFluency"></iframe>
<script>addEventListener("message",function(e){var f=document.getElementById("tf-mini-book-cover-maker");if(f&&e.source===f.contentWindow&&e.data&&e.data.tfEmbedHeight){f.height=e.data.tfEmbedHeight}});</script>
<p>Powered by <a href="https://toolfluency.com/tools-v2/creative/mini-book-cover-maker.html">Mini Book Cover Maker: Print Covers for Tiny &amp; 3D Printed Books</a> — free tools by ToolFluency</p>