Firewood Calculator

Tools and materials for this job

Links go to Amazon. As an Amazon Associate, ToolFluency earns from qualifying purchases.

Heat first, then wood

Most firewood charts jump straight to "a house needs 4 to 6 cords". This calculator starts with the heat. For a heating season it uses Natural Resources Canada's energy use data: for each province, the heat an average single detached house of each age group needs in a year, per square metre of floor. An Ontario house built 1978 to 1995 needs 0.460 GJ per m2; one built before 1946 needs 1.005. If you know last winter's oil, gas, propane or electricity, it uses that instead, at NRCan's average efficiency for your kind of furnace. For an outage, it is the heat you keep up times the hours.

Then it divides by your stove's efficiency, from about 10% for an open fireplace to 60% for a modern EPA-certified stove (University of Missouri Extension, NRCan, EPA), and by the energy in a cord: 80 cubic feet of solid wood (Missouri Extension) at the density the USDA Wood Handbook gives for your wood, at 8,600 Btu per pound of dry wood. A cord of oak works out to 27.1 GJ and weighs about 3,590 lb seasoned, close to Missouri Extension's 3,600 lb. We take the lightest wood in each group, so the cord count never comes out smaller than NRCan's own 30.6 GJ per cord of hardwood would give.

The answer is one number in full cords, rounded up to the quarter cord, because Measurement Canada says to buy firewood by the cord, a fraction of a cord or the stacked cubic metre. Face cords and cubic metres are shown for sellers who use them.

Figures we could not confirm

NRCan's "A Guide to Residential Wood Heating" is no longer on its website and the Internet Archive was offline, so we used NRCan's energy figures as published by Statistics Canada. NRCan does not define its "gross output thermal requirement" in its glossary; we read it as the heat a house's heating system delivers in a normal year (it does not change from 2018 to 2021). NRCan does not say whether its floor space counts basements, so we tell you to count a heated basement, which can only raise the answer. NRCan gives no efficiency for propane furnaces; we use its natural gas figures. The 20% moisture adjustment of wood density is our own interpolation between the Handbook's green and 12% figures. We did not pull model efficiencies from EPA's certified stove list; 60% is the low end of Missouri Extension's 60% to 72%. The 15,000 BTU/h outage default is an example to replace with your own number. We could not open wett.ca to confirm its inspector program. We read NFPA 211 only as quoted by CSIA.

Sources

  1. NRCan Comprehensive Energy Use Database, residential, 2021: gross output thermal requirements per household, single detached housing stock and floor space by vintage, for each province; heating system stock efficiencies.
  2. Statistics Canada, Energy content of various energy sources (citing NRCan) and US EIA, British thermal units.
  3. University of Missouri Extension, G5450 Wood Fuel for Heating: cords, solid wood per cord, heat per pound, appliance efficiencies, face cords and ricks.
  4. USDA Forest Products Laboratory, Wood Handbook (FPL-GTR-282): specific gravity by species, green and at 12% moisture.
  5. Measurement Canada: buying firewood, selling firewood and measuring bulk firewood.
  6. US EPA Burn Wise: energy efficiency and your wood-burning appliance, best wood-burning practices, and the certified wood stove database background.
  7. Health Canada: wood smoke and carbon monoxide.
  8. Chimney Safety Institute of America, homeowner resources (NFPA 211 yearly inspection) and NFPA, home heating safety.

All pages read and checked on November 16, 2026. In an emergency, call 911.

About Firewood Calculator

Divide the heat your house needs by your stove's efficiency and the energy in a cord. An average Ontario house needs about 89 GJ of heat a winter (NRCan); a modern stove at 60% and mixed hardwood at 21.8 GJ per cord make that 6.8 cords, so buy 7 full cords (21 face cords of 16-inch wood, or 24.7 stacked cubic metres). Burn it under 20% moisture and have the chimney inspected every year.

By the ToolFluency team · Updated November 2026

Work out how much firewood to buy for a heating season, from your province, the age of your house and its heated floor area, or from last winter's oil, gas, propane or electricity, or for a power outage of any length. Pick your wood and your stove, from a modern EPA-certified stove to an open fireplace. You get one clear answer in full cords, then the same amount in face cords and stacked cubic metres, with drying, chimney and CO alarm safety beside it. Every figure is sourced and every assumption labelled.

How to work out how much firewood you need

  1. Pick what the wood is for: a heating season or a power outage.
  2. For a season, give your province, when the house was built and its heated floor area, or last winter's heating fuel and furnace type. Set the share of the heat wood will supply.
  3. For an outage, give the heat you will keep up (in BTU/h or kW), the hours a day and the days.
  4. Pick your wood (oak and maple hold the most per cord, pine and poplar the least) and what you burn it in. For a certified stove, type its overall efficiency from EPA's list if you have it.
  5. Read the answer in full cords, then face cords and stacked cubic metres, and check your wood is under 20% moisture before you burn it.

Full cords for a heating season, average single detached house (all ages), modern stove at 60%, mixed hardwood at 21.8 GJ per cord

ProvinceAverage houseHeat a winterBuy
Newfoundland and Labrador150 m2 (1,615 ft2)69.2 GJ5 1/2 cords
Prince Edward Island167 m2 (1,798 ft2)67.3 GJ5 1/4 cords
Nova Scotia156 m2 (1,679 ft2)67.7 GJ5 1/4 cords
New Brunswick151 m2 (1,625 ft2)64.5 GJ5 cords
Quebec148 m2 (1,593 ft2)81.3 GJ6 1/4 cords
Ontario179 m2 (1,927 ft2)89.0 GJ7 cords
Manitoba147 m2 (1,582 ft2)66.9 GJ5 1/4 cords
Saskatchewan151 m2 (1,625 ft2)72.9 GJ5 3/4 cords
Alberta156 m2 (1,679 ft2)79.4 GJ6 1/4 cords
British Columbia191 m2 (2,056 ft2)62.3 GJ5 cords
Yukon, NWT, Nunavut182 m2 (1,959 ft2)100.3 GJ7 3/4 cords

Examples

An Ontario house built 1978 to 1995, 170 m2, heated all winter with wood
NRCan: 0.460 GJ of heat per m2 a year, so 170 x 0.460 = 78.2 GJ. A modern stove at 60% burns 78.2 / 0.60 = 130.3 GJ of wood. Mixed hardwood holds 21.8 GJ per cord: 130.3 / 21.8 = 5.98 cords. Buy 6 full cords, which is 18 face cords of 16-inch wood or 21.7 stacked cubic metres.
Half the heat of 700 US gallons of heating oil, from oak
700 gal x 138,500 Btu (US EIA) x 78% (a mid-efficiency oil furnace, NRCan) = 75.6 million Btu of heat. Wood covers half: 37.8 million Btu. A modern stove at 60% burns 37.8 / 0.60 = 63.0 million Btu of wood. A cord of oak holds 25.7 million Btu (27.1 GJ): 63.0 / 25.7 = 2.45 cords. Buy 2 1/2 full cords (8 face cords).
A week without power, keeping the living area warm
15,000 BTU/h x 24 h x 7 days = 2.52 million Btu (2.66 GJ). A modern stove at 60% burns 2.52 / 0.60 = 4.2 million Btu of wood. Mixed hardwood holds 20.7 million Btu (21.8 GJ) a cord: 4.2 / 20.7 = 0.20 cords. Buy a quarter cord: about 590 lb (270 kg) of seasoned wood, 80 lb a day.

Frequently asked questions

How many cords of wood does it take to heat a house for a winter in Canada?

It depends on the province, the age and size of the house and the stove. NRCan's energy data puts an average Ontario house (179 m2, all ages) at about 89 GJ of heat a winter. With a modern stove at 60% and mixed hardwood at 21.8 GJ per cord, that is 89.0 / 0.60 / 21.8 = 6.8 cords: buy 7 full cords. The same math gives 5 cords for an average New Brunswick or British Columbia house and 6 1/4 for Quebec or Alberta. Houses built before 1946 need about twice the heat per square metre of ones built after 1995.

What is the difference between a face cord and a full cord?

A full cord is a stack 4 ft high, 4 ft deep and 8 ft long: 128 cubic feet, about 3.62 stacked cubic metres. A face cord is one row 4 ft high and 8 ft long, as deep as the pieces are long; with 16-inch pieces it is one third of a full cord, so 3 face cords make a full cord. Measurement Canada says to buy by the cord, a fraction of a cord or the stacked cubic metre, and calls "face cord" an illegal term for selling firewood.

How much firewood do I need for a power outage?

Multiply the heat you will keep up by the hours: 15,000 BTU/h for 24 hours a day for 7 days is 2.52 million Btu. A modern stove at 60% burns 2.52 / 0.60 = 4.2 million Btu of wood, and a cord of mixed hardwood holds about 20.7 million Btu (21.8 GJ), so you need 0.2 cords: buy a quarter cord, about 590 lb of seasoned wood, or about 80 lb a day.

How much heat is in a cord of wood?

A cord holds about 80 cubic feet of solid wood (Missouri Extension). With USDA Wood Handbook densities at 20% moisture and 8,600 Btu per pound of dry wood, a cord of oak, hickory, sugar maple or beech holds about 25.7 million Btu (27.1 GJ), ash or yellow birch 24.7 million (26.1 GJ), red maple, white birch, cherry or elm 20.7 million (21.8 GJ), and pine, spruce, fir or poplar 14.0 million (14.8 GJ). NRCan gives 30.6 GJ for hardwood and 18.7 GJ for softwood; US EIA uses 20 million Btu for any cord.

How long does firewood need to dry?

EPA says at least 6 months for softwood and at least 12 months for hardwood, and to burn wood under 20% moisture, tested with a wood moisture meter. Health Canada says at least 6 months. Split pieces 6 inches across or smaller, stack them off the ground and cover only the top.

How often should a chimney be inspected?

At least once a year. Health Canada says a qualified professional should inspect a wood stove at least once a year and the chimney should be cleaned regularly; NFPA 211 says chimneys, fireplaces and vents are inspected at least once a year (as quoted by CSIA), and NFPA says to inspect and clean them each year before the season.

Is an open fireplace a good way to heat a house?

No. Missouri Extension puts a traditional fireplace at about 10% efficient, and in some cases worse than nothing, and EPA says fireplace drafts pull warm air up the chimney and make other rooms cooler. An EPA-certified insert or stove gets far more heat from each cord.

How many cubic metres are in a cord of wood?

A full cord is 128 cubic feet, about 3.62 stacked cubic metres. Measurement Canada says to divide cubic metres by 3.6 to get cords, and recommends buying by the stacked cubic metre.
Disclaimer: Estimates from NRCan, Statistics Canada, US EIA, USDA and University of Missouri figures, checked against the sources on 2026-11-16. Real houses, stoves and woodpiles vary: a cord can hold 65 to 90 cubic feet of solid wood, and wet wood gives less heat. Have your chimney and stove inspected every year, keep smoke and CO alarms working, and follow your stove's manual and local fire rules. If a CO alarm sounds, get outside, then call 911.

Part of ToolFluency’s library of free online tools for Emergency Prep. No account needed, no data leaves your device.

Embed this tool on your site (free)
Paste this where you want the tool. Please keep the attribution link.
<iframe id="tf-firewood-calculator" src="https://toolfluency.com/tools-v2/emergency/firewood-calculator.html?embed=1" width="100%" height="640" loading="lazy" style="border:1px solid #e2e2e2;border-radius:12px;max-width:760px" title="Firewood Calculator by ToolFluency"></iframe>
<script>addEventListener("message",function(e){var f=document.getElementById("tf-firewood-calculator");if(f&&e.source===f.contentWindow&&e.data&&e.data.tfEmbedHeight){f.height=e.data.tfEmbedHeight}});</script>
<p>Powered by <a href="https://toolfluency.com/tools-v2/emergency/firewood-calculator.html">Firewood Calculator</a> — free tools by ToolFluency</p>